Engine - Performance Parts for 1986-92 MKIII

Introducing a high quality drain plug with a strong magnet for your Supra or Skyline! You can see proof of the quality of this drain plug on a youtube clip.

Fits all Toyotas and Nissans with a thread sizing of M12xP1.25.

The Xtreme HID Conversion kits utilize cutting edge HID components made with superior Japanese craftsmanship and quality. These kits are manufactured in a high tech facility that is ISO and TUV certified!! Laser calibrated bulbs are used to ensure proper fitment and optically correct beam patterns. Don't sacrifice quality when it comes to your car!

The ballasts used in this product are uniquely designed for aftermarket applications as they are completely epoxy sealed to protect against harsh weather conditions. In aftermarket applications, ballasts are often mounted outside the headlight leaving them susceptible to water damage. The Xtreme ballasts are specifically designed for these applications making them the superior choice for your aftermarket HID upgrade.


BALLAST SPECIFICATIONS:

- Xtreme HID ballasts are designed with a patented multi stage safety feedback (M.S.S.F.) system allowing them to interact with the bulbs to determine optimal light output.

- Xtreme HID ballasts use a patented self intelligent light output configuration (S.I.L.C) to ensure brightness stability and precise illumination colour.

- The Xtreme HID ballasts are designed for both 12V and 24V applications.

- Equipped with advanced polarity protection system

You can get these in the kelven temperature listed below. which ever you prefer just give me the bulb size whether it be for your low, high or even fog if you want to go all out.

This product will include 2 complete wiring harnesses - 1 per side that will literally plug directly into your OEM headlight harnesses via proper mating connectors. The harnesses provided will include upgraded fuses and relays to ensure you do not draw a higher current from your stock wiring harness than it was designed to provide. Unlike many kits on the market, each harness will be completely independent of the other so should a fuse ever fail, you will still have a functioning headlight. Most other HID kits that come with a harness use a single relay/fuse design that will result in you losing both your headlights if the harness fails.

We will back up 100% with a manufacturers Warranty and personally vouch for quality on these kits that we're running in almost every vehicle the company owns ie: trucks and Supra's, Bikes etc. around here and have yet to fail! These are 100% Plug and Play and can be installed in a matter of minutes, that is if you know what your doing. Again its plug and play and you cant get it wrong!!!!

We are now offering the new Braille Carbon Fiber Batteries to support the power needs with the clean look of carbon fiber that can mount any which way for your vehicle application.

B106 Carbon Fiber Race Battery Specs
Casing: Carbon Composite Shell & Polymer Plastic
Weight: 6 lbs
Length: 5.8
Width: 3.4
Height: 4.2
Pulse Cranking Amps (PCA): 527
Warranty: 1 Year Replacement

B14115 Carbon Fiber Battery Specs
Casing: Carbon Composite Shell & Polymer Plastic
Weight: 11.5 lbs
Length: 5.8
Width: 3.4
Height: 5.8
Pulse Cranking Amps: 904
Cranking Amps: 486
Cold Cranking Amps: 360
Amp Hour Rating: 15
Warranty: 1 Year Free Replacement

B2015 Carbon Fiber Battery Specs
Casing: Carbon Composite Shell & Polymer Plastic
Weight: 15 lbs
Length: 6.8
Width: 3.4
Height: 6.1
Pulse Cranking Amps: 1067
Cranking Amps: 574
Cold Cranking Amps: 425
Amp Hour Rating: 21
Warranty: 1 Year Free Replacement / 2 Year Limited Pro-Rated Extended Coverage
Battery Type: Sealed Rechargeable Deep-Cycle
Mounting: Vertical or Horizontal

Braille B3121 Carbon Fiber Premium & Extreme Use Lightweight BatteryPERFORMANCE
Voltage: 12 volts
Full Charge Voltage: 13.8 volts
Short Circuit Current (Max Cranking Amps): 3000
Pulse Cranking Amps (PCA) 5 sec @ 80F: 1380
Pulse Cranking Amps (PCA) 10 sec @ 80F: 1207
Pulse Cranking Amps (PCA) 20 sec @ 80F: 1066
Cranking Amps 30 sec @ 80F: 892
Cranking Amps 30 sec @ 32F: 742
Cold Cranking Amps 30 sec @ 0F: 550
Reserve Capacity: 1hr &15minutes
Capacity (C/20 rate): 31 amp hr
Internal Resistance (ohms): 4 milliohms (.004ohms)
Life Cycle @ 10% DOD: Up to 3500 cycles

PHYSICAL SPECS
Carbon Fiber Heat-Resistant Casing, Horizontal and Vertical Mounting
BCI Group: Usable for all Group Sizes
Length: 6.6
Width: 5.1
Height: 6.8
Minimum Weight (lbs): 21 lbs
Post Type: SAE Automotive Posts included & 6 x 1.0mm racing bolts included.
Stainless Stud: Both Automotive SAE Posts and Race Style Bolts are Stainless with a 6 x 1.0mm bolt pitch

Note:

CM's machined aluminum housings replace stock spin-on filters and accepts CM's proprietary high flow synthetic oil filter elements. Designed to withstand the highest pressure surges and rough duty service. These blue anodized housings have a removable bottom threaded cap. Element replacement is done through the bottom cover which is threaded into the body.

CM spin-on oil filters are offered in several different combinations of mounting thread and sealing gaskets, along with two lengths to fit most engine applications. Each housing comes complete with all the necessary O-rings and gaskets required, and one 8 micron element.

Note: Replacement Filters in single or 6pack's, Replacement Spin-On O-ring kits all available.

CM's machined aluminum housings replace stock spin-on filters and accepts CM's proprietary high flow synthetic oil filter elements. Designed to withstand the highest pressure surges and rough duty service. These blue anodized housings have a removable bottom threaded cap. Element replacement is done through the bottom cover which is threaded into the body.

Note: Please choose desired item that is needed to be replaced below.

GReddy Oil Catch Tanks collect the oil, moisture and blow-by gases that cause carbon and sludge build-up in the intake system and engine to keep them clean even under the hardest driving conditions. The Traditional (Sq.) model holds 500ml and can be mounted vertically or horizontally, while the high capacity 1000ml Lightweight (Oval) is better suited for vertical mounting.

Anyone that has ever tried to connect a boost gauge, electronic boost controller, fuel controller, fuel pressure regulator, blow off valve, and TPS sensor to the intake plenum knows all to well the mess of hoses and tees and connections going everywhere from a single source. Well we had enough also, so we designed the VDP (Vacuum Distribution Plenum) to simplify hose routing. Now, a single 6mm hose connection to the intake plenum gives you 6 hose connections, enough to run any combination of sensors, gauges, and components. What's more, the hose barb connections are universal 1/8" NPT and can be removed and replaced with AN fittings for completely secure hose connections in race applications. Mounting provisions are universal, with two 3/8-16 tapped bolt holes in the rear for mounting to any bracket, firewall, or as desired in any position. Anodized red with the PHR logo, fittings included.